Connect the lights on your trailer, motorcycle or bicycle carrier.
The unit reads your vehicle’s CANBUS/LINBUS signals and controls the lights on the connected accessory through a 13-pin socket. Indicators, brake lights, position lights and reversing lights: your movements are visible behind you, too.
Bring your passions along. Connect the accessory’s lights to your motorhome.
Towbars & trailers
A 13-pin socket to manage the lighting signals on the connected trailer.
THE FEATURES THAT MAKE A DIFFERENCE
More possibilities. Less complexity.
From newer vehicle networks to everyday installation: one interface, designed to simplify your work.
NEXT-GENERATION VEHICLES
CAN FD
Ready for CANBUS FD.
Communicates with the CAN FD networks used on newer vehicles, alongside CANBUS 2.0 and LINBUS. Technology that keeps pace with vehicle development.
CANBUS FDCANBUS 2.0LINBUS
SIMPLER INSTALLATION
Fewer wires. Less time.
Reads signals from the vehicle’s data network, reducing connections compared with conventional units. Vehicle recognition is automatic: no DIP-switch or app setup is required.
LED +
LED and conventional bulbs.
The power outputs support both types of lighting, for different accessories and configurations.
1
One interface. Multiple vehicles.
The same unit covers all compatible models. No need to stock a different control unit for each vehicle.
C2
Bulb failure monitoring.
C2 monitoring provides an audible warning if a trailer indicator bulb fails, helping you identify the fault.
P
Parking sensor cut-off.
At ignition-on, trailer detection can activate the contact that disables parking sensors when an accessory occupies their detection area.
EVERY OUTPUT, EXPLAINED
The signals you need.
Already available.
Eight electrical outputs to connect your accessory’s lighting and provide an ignition-switched positive supply.
8dedicated outputs 12 V
The lighting outputs power the lamps directly, without additional amplification relays. The kit includes the wiring harness and 13-pin socket.
Replicates the left-turn signal on the accessory’s lights.
02
Right indicator
Replicates the right-turn signal on the accessory’s lights.
03
Brake lights
Controls the stop lamps to indicate braking on the trailer too.
04
Left position lights
Provides the signal for the position lights on the left side.
05
Right position lights
Provides the signal for the position lights on the right side.
06
Reverse light
Activates the dedicated lamp when reverse gear is engaged.
07
Rear fog light
Controls the accessory’s rear fog light, including separately from the vehicle’s light through the dedicated function.
08
Switched positive supply
Provides a positive 12 V supply with the ignition on, useful for integrating caravan services.
DESIGNED TO SIMPLIFY
One connection. So many possibilities.
Communicates with your vehicle
Automatic recognition through the data network and fewer wire connections than conventional control units.
The right light at the right time
Indicators, brake lights, position lights, reverse, rear fog and switched positive supply: 8 outputs for the connected accessory.
Attention to every detail
C2 bulb monitoring with an audible alert, short-circuit protection and compatibility with LED and conventional lighting.
FROM YOUR VEHICLE TO YOUR PASSIONS
Technology works. You travel.
Your vehicle
CANBUS 2.0 · CAN FD · LINBUS
Van Service Towbar
Reads signals and manages outputs
Your accessory
13-pin socket · LED and conventional lights
Connection to the data network reduces the number of wires needed. Updatable firmware allows compatibility to grow over time. The Paser team can help check the solution for your specific vehicle version.
SMALL DETAILS, A BIG DIFFERENCE
Designed for the details you don’t see.
Trailer detection
When the ignition is switched on, the unit checks for a trailer and can activate the contact to disable parking sensors. Useful when the accessory sits within their detection range.
A failed indicator? You know.
C2 monitoring provides an audible warning of indicator bulb failure. With the backup function enabled, a position light can be used as an indicator if the indicator bulb fails.
An installation you can check
Self-test mode activates outputs in a defined sequence, allowing the installer to check the lights before handing over the vehicle. Four auxiliary inputs help integrate signals unavailable on the data network.
COMPATIBILITY
Find your travel companion.
Models listed in the brochure. Contact us to check your specific vehicle version and available updates.
Compatible vehicles
Brand
Model
Year
Fiat
Ducato
2021 →
Ford
Transit
2025 →
MAN
TGE
2024 →
Mercedes
Sprinter
2022 →
Mercedes
Vito
2021 →
Renault
Master
2026 →
Volkswagen
Crafter
2024 →
THE KIT & RESOURCES
Ready to connect.
Control unit, loose-wire wiring harness and 13-pin socket included. See the documentation for specifications and installation instructions.
Fiat
Ford
MAN
Mercedes
Renault
Volkswagen